DC Cargo Mall Recessed D Ring Tie Down Anchors (10 Pack)

DC Cargo Mall Recessed D Ring Tie Down Anchors (10 Pack)

This 10-pack kit includes 4-3/4″ x 4-1/2″ square D RING recessed pan fitting tiedowns with 6.5″ x 6.5″, 1/10″ thick BLACK STEEL mounting BACK PLATES for trailer underside, and installation hardware accessories BOLTS, nuts, and washers
ANCHOR logistic ratchet and cam straps, tarp straps, bungee cords, motorcycle tie-downs, chains, and ropes on pickup truck beds, flatbeds, in enclosed trailers, boats, and vans by inserting S or J hooks through the 1 1/2″ x 1 1/2″ inner clearance D ring tie downs
The 13/32″ diameter countersunk bolting holes in the pan fitting corners provide a low flush surface; Use the included Grade A ASTM A307 2.5″ long 3/8″ diameter round carriage head bolts, ANSI B1.1 Class 2B lockwasher Keps (K) nuts with attached free spinning toothed serrated star washers, and 3/32″ flat washers

 

10-Pack Trailer Flush Mount D Ring Cargo Tie-Down Anchor

When you need a secure and convenient cargo tie-down anchor, choose this flush mount D ring and mounting plate installation kit. The galvanized D ring has a square recessed pan that gets bolted into your wooden trailer floor, keeping your surface even and avoiding the hazards of people tripping and freight snagging. The D ring lies flush in the pan when not in use and can be lifted upward for use as a cargo tie-down anchor.

Installing & Using the Square Recessed D Ring Pan Fitting

Use a hole saw and chisel to cut 2-7/8″ x 2-5/8″ hole in your wooden floor. Because the recessed pan fitting is deeper on one side, the hole should gradually advance from 1/2″ – 3/4″ deep. This recessed pan fitting has a pre-drilled countersunk hole in each corner with the holes narrowing on bottom and widening towards the surface, ensuring that the bolts remain flush with the surface and do not rise above it. Secure each bolt with a washer and nut on the other side of the mounting surface.

Flush mount D ring fittings have weep holes in the pans to allow for water drainage. This D ring is galvanized to resist corrosion and rust.

Steel Mounting Back-Plate, Installation Pack Includes 4 Bolts, 4 Nuts, 4 Washers

This mounting back-plate goes on the underside of the mounting trailer to reinforce the lock hold. It is a black 1/10″ thick, 6.5″ x 6.5″ square plate with a 3.5″ diameter circle in the middle. Each plate has four pre-drilled holes for bolting down.

The 3/8″ diameter, 2.5″ long round head carriage are Grade A ASTM A307. The 3/8″ diameter, 3/8″ thick lockwasher Keps (K) nuts have attached free spinning toothed serrated star washers; they conform to ANSI B1.1 Class 2B standards. The 1″ diameter flat washers are 3/32″ thick. The bolts, nuts, and washers are all made out of steel and plated with zinc for superior strength as well as corrosion- and rust- resistance.
This 10-pack kit includes 4-3/4″ x 4-1/2″ square D RING recessed pan fitting tiedowns with 6.5″ x 6.5″, 1/10″ thick BLACK STEEL mounting BACK PLATES for trailer underside, and installation hardware accessories BOLTS, nuts, and washers
ANCHOR logistic ratchet and cam straps, tarp straps, bungee cords, motorcycle tie-downs, chains, and ropes on pickup truck beds, flatbeds, in enclosed trailers, boats, and vans by inserting S or J hooks through the 1 1/2″ x 1 1/2″ inner clearance D ring tie downs
The 13/32″ diameter countersunk bolting holes in the pan fitting corners provide a low flush surface; Use the included Grade A ASTM A307 2.5″ long 3/8″ diameter round carriage head bolts, ANSI B1.1 Class 2B lockwasher Keps (K) nuts with attached free spinning toothed serrated star washers, and 3/32″ flat washers
The D RING TIEDOWN ANCHOR is made out of GALVANIZED STEEL, the trailer mounting lock plate is made out of durable black STEEL and the bolts, nuts, and washers are all made out of zinc-plated steel -ensuring superior strength as well as corrosion and rust-resistance
Assembly Break Strength is 6,000 pounds and Working Load Limit is 2,000 pounds; Our friendly customer service representatives are always available and we offer a 100% money-back satisfaction guarantee

DC Cargo Mall Recessed D Ring Tie Down Anchors (10 Pack)

 out of stock
Amazon.com
as of March 27, 2024 5:47 am

Features

  • This 10-pack kit includes 4-3/4" x 4-1/2" square D RING recessed pan fitting tiedowns with 6.5" x 6.5", 1/10" thick BLACK STEEL mounting BACK PLATES for trailer underside, and installation hardware accessories BOLTS, nuts, and washers
  • ANCHOR logistic ratchet and cam straps, tarp straps, bungee cords, motorcycle tie-downs, chains, and ropes on pickup truck beds, flatbeds, in enclosed trailers, boats, and vans by inserting S or J hooks through the 1 1/2" x 1 1/2" inner clearance D ring tie downs
  • The 13/32" diameter countersunk bolting holes in the pan fitting corners provide a low flush surface; Use the included Grade A ASTM A307 2.5" long 3/8" diameter round carriage head bolts, hex nuts, and 3/32” flat washers
  • The D RING TIEDOWN ANCHOR is made out of GALVANIZED STEEL, the trailer mounting lock plate is made out of durable black STEEL and the bolts, nuts, and washers are all made out of zinc-plated steel –ensuring superior strength as well as corrosion and rust-resistance
  • Assembly Break Strength is 6,000 pounds and Working Load Limit is 2,000 pounds
DMCA.com Protection Status      © 2024 CarAudioNow.com